Home > Cannot Verify > Cannot Verify File System Mount Point

Cannot Verify File System Mount Point

If yes, what was the solution?   I've already tried deleting the drives and re-configuring them but this does not help. Hot Network Questions If I receive written permission to use content from a paper without citing, is it plagiarism? Perhaps it'll help someone else. Showing results for  Search instead for  Do you mean  Menu Categories Solutions IT Transformation Internet of Things Topics Big Data Cloud Security Infrastructure Strategy and Technology Products Cloud Integrated Systems Networking Check This Out

I can connect to the share \\server\dir either on the "Run..." prompt or when I enter the path in Windows Internet Explorer. Solved! How can I determine which device (i.e., /dev/sda2) is going to show up in /proc/mounts in general given that the bind mount may be to a directory/file that is potentially "obscured" Data Protector 8.00 can be downloaded from HP website, the download will be available on 2013/06/26.

0 0 06/13/13--09:47: Configure Disk Device - HP Data Protector 7 Contact us about https://community.hpe.com/t5/Data-Protector-Practitioners/Unable-to-backup-filesystem-mount-81-72/td-p/5178873

They are both major 8, minor 18. When prompted, I enter the password for this account (just happens to be the DP service account). All good.   Now I try to run it.   Starts fine, loads medium to device OK. Your file systems of interest are type ext3, per your mount -v output.Now, the DP GUI can be a bit confusing in this regard.

When running it I got the following message   Warning] From: [email protected] "Drive0" Time: 14/06/2013 09:36:33 Block size of [email protected] (16Kb) does not match this device (512Kb). Community Data Protector Practitioners Forum CommunityCategoryBoardUsers turn on suggestions Auto-suggest helps you quickly narrow down your search results by suggesting possible matches yes no add cancel (Page 1) | 2 | 3 | 4 | .... | 141 | newer HOME | ABOUT US | CATALOG | CONTACT US | ©2016http://www.rssing.com Community Data Protector Practitioners Forum CommunityCategoryBoardUsers turn on suggestions Auto-suggest helps you quickly narrow down your search results by suggesting possible matches

I also included it on my backup specification. An extened omnidbcheck is good:   Core -core OKFilenames -filenames OKDCBF(presence and size) -bf OKSIBF(readability) -sibf OKOMNIDC(consistency) -dc OKDONE!   I recreated the backups, tested one and it ran good.  I I again receive an error 81:72 "Cannot verify filesystem mount point: ([3] The system cannot find the path specified" I can access the local drive from the Cell Manager. https://community.hpe.com/t5/Data-Protector-Practitioners/error-messages-cannot-verify-filesystem-mount-point/td-p/2634519 I try other capacity, but this behavior repeat.   My block size on tape drive and disk drive devices are 256 k.   My windows driver letter (f:) is with compression

I try this copying just one media with 10 GB and the time spent was almost one hour. I find consulting /proc/partitions to be the fastest. UNIX is a registered trademark of The Open Group. This would be the /puma right under the client name, not /puma under / under the client name.Let's say you don't want /bin.

When using the Manager-of-Manager feature up to 5000 clients can be protected and up to 2.5 billions media can be managed with HP Data Protector. It's important to understand/remember that the name of a device file like /dev/sda1 is only a label. You're trying to back up /, /puma, and /pumabkup. I am then back at the source selection screen and can drill down into the CIFS share and make my target selections.

From: [email protected]**********\\**********\*******" Time: 14/12/2005 16:31:50 UNC\**********\*********\09September\X_DONE - DAY\30-09-05\Thumbs.db Cannot open: ( A required privilege is not held by the client. ) => not backed up. 0 Kudos Reply The opinions expressed his comment is here Browse other questions tagged mount directory block-device or ask your own question. Any suggestions??Thank you all in advance,Thorsten Becker Dang... That value can be separated into two bytes, 8 and 1.

In a local copy of disks i have 150/250 MB/s.   In any backup the maximum is de 45MB/s ( Network or SAN ) of one client. Checked with all the permission andeverything looks ok. can someone help?     thanks

0 0 06/14/13--00:47: Block size does not match this device - DP 7.01 Contact us about this article I'm configuring a copy job from this contact form Data Protector only supports backing up data from certain kinds of file systems.

It's even a test direktory, where every user has full right.I also checked the user settings in the DP users menu. From: [email protected] "\\acme\H$" Time: 10/12/2005 12:25:30 ABORTED Disk Agent for acme7:\\acme\H$ "\\acme\H$". 0 Kudos Reply All Forum Topics Previous Topic Next Topic 3 REPLIES BR894765 Valued Contributor [Founder] Options Mark as this thread has been moved from Tape Backup (Small and Medium Business) to Data Protector - Hp Forum moderator  

0 0 06/09/13--05:28: Facing problem while importing linux IS to windows

Those are raw devices.

So, the next step is to figure out what device major 8, minor 1 is. I have clients installed to many servers within the customer domain, and can backup flat file, exchange, SQL without issue.   When I setup a "map network share" type of job, Copy med... 06/13/13--02:16: _Stumped..."Invalid ... 06/13/13--09:28: _HP Data Protector 8... 06/13/13--09:47: _Configure Disk Devi... 06/14/13--00:47: _Block size does not... 06/14/13--13:07: _Debian (showing articles 1 to 20 of 2811) Browse the Latest can you telnet to your linux server on port 5555?is there any useful information in the log files in /var/opt/omni/log/ on your linux server? 0 Kudos Reply Scott McIntosh_2 Honored Contributor

We can confirm this with an ls -l /dev/sda1 brw-rw---- 1 root disk 8, 1 May 8 05:33 /dev/sda1 Notice the 8, 1 before the datestamp. Can I get a help?"1What is a block device?2How to make sure that certain devices always use the same device file? Here it lists 801h. navigate here My server is one of my company main server and always up.

I am having problems performing a backup to one of my server. Showing results for  Search instead for  Do you mean  Menu Categories Solutions IT Transformation Internet of Things Topics Big Data Cloud Security Infrastructure Strategy and Technology Products Cloud Integrated Systems Networking P.S. Not sure what is happening here....   Cheers, Timo       P.S.

Community Data Protector Practitioners Forum CommunityCategoryBoardUsers turn on suggestions Auto-suggest helps you quickly narrow down your search results by suggesting possible matches

Back to Top